Robot Pi Shop

PZEM-004T Current Voltage Multimeter Module AC 80-260V 100A with Current Transformer

$10.99

Shipping calculated at checkout.

Quantity

PZEM-004T AC Voltage, Current & Power Energy Meter Module 80–260V 100A

The PZEM-004T AC Power and Energy Monitoring Module is designed to measure electrical parameters in single-phase AC systems, including voltage, current, active power, energy consumption, frequency, and power factor.

Featuring an external 100A current transformer (CT), the module allows current measurement without directly routing the load current through the measurement board.

The PZEM-004T supports serial communication, making it suitable for integration with Arduino, ESP32, ESP8266, Raspberry Pi, and other microcontroller-based monitoring systems through appropriate interface circuitry.

It is an excellent solution for smart energy monitoring, home automation, electrical consumption analysis, and IoT power measurement projects.

Key Features

  • Multifunction Energy Monitoring: Measures AC voltage, current, active power, energy consumption, frequency, and power factor.
  • Wide Voltage Measurement Range: Supports 80–260V AC.
  • High Current Measurement: Measures up to 100A using an external current transformer.
  • Energy Consumption Tracking: Measures accumulated electrical energy in kilowatt-hours (kWh).
  • UART Communication: Serial interface for integration with microcontrollers and monitoring systems.
  • Digital Measurement: Provides electrical measurements for software-based monitoring and analysis.
  • External Current Transformer: Allows non-invasive current sensing around a single conductor.
  • Compact Module: Suitable for integration into electrical monitoring projects.
  • IoT Compatible: Can be integrated with ESP32, ESP8266, Arduino, and Raspberry Pi using suitable communication interfaces.

Technical Specifications

Parameter Specification
Model PZEM-004T
Module Type AC Power and Energy Monitoring
Voltage Measurement Range 80–260V AC
Current Measurement Range 0–100A AC
Current Sensor External Current Transformer (CT)
Active Power Measurement Up to approximately 26kW
Energy Measurement kWh
Frequency Measurement 45–65Hz (typical)
Power Factor Measurement Supported
Communication Interface TTL Serial / UART
Communication Baud Rate 9600 bps
Serial Logic Supply 5V DC (version-dependent interface requirements)
Measurement Type Single-Phase AC
CT Opening Diameter Approximately 33mm (listed)
Board Dimensions Approximately 74 × 31mm (listed)
Compatible Platforms Arduino, ESP32, ESP8266, Raspberry Pi (with appropriate interface)

Specifications are based on commonly available PZEM-004T modules. Communication protocol and detailed measurement characteristics depend on the hardware revision.

Measured Electrical Parameters

Parameter Description
AC Voltage Measures the RMS voltage of the connected AC supply
AC Current Measures load current through the external CT
Active Power Measures real electrical power consumption in watts
Energy Consumption Tracks accumulated energy usage in kWh
Frequency Measures AC supply frequency in Hz
Power Factor Indicates the relationship between active and apparent power

Connection and Integration

1. AC Voltage Measurement

Connect the voltage measurement terminals according to the wiring diagram supplied for the specific module revision.

2. Current Transformer

Place the external current transformer around a single live or neutral conductor supplying the load. Do not place both conductors through the same CT opening.

3. UART Communication

Connect the module's serial interface to a compatible microcontroller or serial adapter, observing the correct signal levels and electrical safety requirements.

4. Software Monitoring

Read measurement data through the supported serial protocol and display or record the results using compatible software.

Applications

  • Smart Home Energy Monitoring
  • Single-Phase AC Power Measurement
  • Electrical Consumption Monitoring
  • IoT Energy Monitoring Projects
  • Arduino and ESP32 Power Monitoring
  • Raspberry Pi Energy Data Logging
  • Electrical Equipment Monitoring
  • Home Automation Systems
  • Laboratory Power Measurement
  • Energy Management Prototypes

Important Notes

  • AC Measurement Only: Designed for compatible single-phase AC systems, not DC measurement.
  • Mains Voltage Hazard: Installation involves potentially lethal AC voltages and should be performed by a qualified person.
  • Current Transformer: Install the CT around only one conductor to obtain a correct current measurement.
  • Communication Interface: UART signal voltage and interface isolation must be verified before connecting a microcontroller.
  • ESP32 and ESP8266: These devices use 3.3V logic and may require appropriate level shifting or an isolated interface.
  • Raspberry Pi: Use a suitable UART interface with verified electrical isolation and voltage compatibility.
  • Not a Protective Device: This module is intended for monitoring and must not replace a circuit breaker, fuse, or certified protective equipment.
  • Hardware Revision: Confirm the module version before selecting a software library or communication protocol.
  • Electrical Isolation: Do not assume that the communication interface is safely isolated from mains voltage without verifying the specific board design.

Package Includes

  • 1 × PZEM-004T AC Power and Energy Monitoring Module
  • 1 × External 100A Current Transformer

USB adapter, display, and microcontroller are not included.

Function:

  1. Electrical parameter measurement function such as voltage, current, connected load and total consuption.
  2. The power button clear function.
  3. Power-down data storage function (cumulative power down before saving).
  4. The serial communication function (comes with TTL serial interface, via various terminals communicate with the adapter plate, read, and set the parameters).

Display Format

1. Power: measurement range 0 ~ 22kW

  • 0 ~ 10kW within the display format of 0.000 to 9.999;
  • Within 10 ~ 22kW display format 10.00 ~ 22.00.

2. Power: measurement range 0 ~ 9999kWh

  • 0 ~ 10kWh within the display format of 0.000 to 9.999;
  • 10 ~ 100kWh within the display format of 10.00 to 99.99;
  • 100 ~ 1000kWh within the display format of 100.0 to 999.9;
  • 1000 ~ 9999kWh and above the display format from 1000 to 9999.

3. Voltage: Test Range 80 ~ 260VAC

  • Display Format 110.0 ~ 220.0.

4. Current: measurement range 0 ~ 100A

  • Display Format 00.00 to 99.99.

Button:

A built-in button on the panel, used to make an electricity clear function.
Electricity clear method: Press ZERO key five seconds, then release the button!
Press again to clear the key, the data is cleared and exit charge cleared, cleared so far completed.

Serial Communication:

The module is equipped with a TTL serial data communication interface via the serial port can be read and set the relevant parameters; but if you want a device with a USB or RS232 (such as computers) to communicate, then you need to be equipped with different TTL adapter hardware board (USB communication needs with TTL to USB adapter plate; RS232 communication needs with TTL to RS232 adapter plate), the adapter plate of the specific connection details can be found in FIG.

Considerations:

1. This module is suitable for indoor, not outdoor use.
2. the applied load should not exceed the rated power.
3. The wiring can not be wrong.