Robot Pi Shop

AM2302 DHT22 Sensor

$4.99

Shipping calculated at checkout.

Quantity

AM2302 DHT22 Digital Temperature & Humidity Sensor – High Accuracy

The AM2302 (DHT22) is a digital temperature and relative humidity sensor designed for environmental monitoring, weather stations, IoT systems, greenhouse automation, HVAC projects, and microcontroller applications.

It combines a capacitive humidity sensing element, temperature sensor, and internal signal-processing circuitry to provide calibrated digital temperature and humidity readings through a simple single-wire data interface.

Compared with the DHT11, the DHT22/AM2302 provides a wider measurement range, higher resolution, and better accuracy, making it more suitable for applications requiring improved environmental measurements.

Technical Specifications

  • Model: AM2302 / DHT22
  • Sensor Type: Digital Temperature & Humidity Sensor
  • Supply Voltage: 3.3–5.5V DC
  • Recommended Supply Voltage: 5V
  • Humidity Measurement Range: 0–99.9% RH
  • Humidity Accuracy: ±2% RH at 25°C
  • Humidity Resolution: 0.1% RH
  • Humidity Repeatability: ±0.3% RH
  • Humidity Response Time: <5s under specified conditions
  • Typical Humidity Drift: <0.5% RH/year
  • Temperature Measurement Range: -40°C to +80°C
  • Temperature Accuracy: ±0.5°C typical
  • Temperature Resolution: 0.1°C
  • Temperature Repeatability: ±0.2°C
  • Temperature Response Time: <10s under specified conditions
  • Communication: Proprietary Single-Bus Digital Interface
  • Output: Calibrated Digital Signal
  • Resolution: 16-Bit Measurement Data
  • Typical Average Current: Approx. 300µA
  • Typical Measurement Current: Approx. 500µA

Temperature & Humidity Measurement

The AM2302 provides both temperature and relative humidity measurements from a single sensor, reducing the number of components required for environmental monitoring projects.

The sensor is factory calibrated, with calibration coefficients stored internally and automatically applied during measurement.

This allows the connected microcontroller to receive already processed digital measurement data rather than having to measure a small analog sensor signal directly.

Digital Single-Wire Interface

Communication with the AM2302 uses a single digital data line, allowing both temperature and humidity readings to be obtained using only one microcontroller GPIO pin in addition to power and ground.

The data line normally requires a suitable pull-up resistor when one is not already included on the breakout board or module.

Although commonly described as a single-wire or one-wire interface, the DHT22 protocol is proprietary and should not be confused with the Dallas/Maxim 1-Wire® protocol used by sensors such as the DS18B20.

Pin Configuration

For the standard 4-pin bare AM2302/DHT22 sensor, viewed from the front with the ventilation openings facing you:

Pin 1 – VDD / Power
Pin 2 – DATA / Serial Data
Pin 3 – NC / Not Connected
Pin 4 – GND / Ground

Always verify the markings if the sensor is supplied on a separate breakout board, as module pin arrangements can differ.

Microcontroller Compatibility

The AM2302/DHT22 is commonly used with:

Arduino
ESP32
ESP8266
STM32
Raspberry Pi Pico
Raspberry Pi with suitable GPIO software

DHT22/AM2302 libraries are widely available for common development platforms, simplifying integration into IoT and environmental-monitoring projects.

Sampling Rate

The DHT22 is intended for relatively slow environmental measurements rather than high-speed data acquisition.

A complete measurement cycle takes approximately 2 seconds, so the sensor should generally not be polled faster than approximately once every 2 seconds.

This is well suited to temperature and humidity monitoring, where environmental conditions normally change relatively slowly.

Applications

Ideal for weather stations, greenhouse monitoring, smart agriculture, HVAC systems, indoor climate monitoring, IoT environmental sensors, incubators, terrariums, home automation, server-room monitoring, data logging, educational electronics, Arduino projects, ESP32 projects, and Raspberry Pi environmental monitoring.

Important Note

The AM2302/DHT22 is designed primarily for general environmental monitoring and embedded electronics projects. It should not be treated as a laboratory-grade precision instrument where certified or traceable measurements are required.

For reliable readings, avoid placing the sensor directly beside heat-generating components, voltage regulators, processors, motors, or other devices that could influence the measured temperature.

Allow adequate airflow around the sensor and avoid condensation or prolonged operation outside its specified environmental conditions.

Package Includes

1 × AM2302 DHT22 Digital Temperature & Humidity Sensor