Robot Pi Shop

KY-034 Automatic Flashing Color LED

$1.25

Shipping calculated at checkout.

Quantity

KY-034 Automatic Flashing Color LED Module – 7 Color RGB LED for Arduino & ESP32

The KY-034 Automatic Flashing Color LED Module is a compact, self-flashing LED module designed to produce automatic multicolor lighting effects without requiring complex programming.

Featuring a 5mm RGB LED with an integrated color-changing controller, the module automatically cycles through different colors when powered. Unlike conventional RGB LED modules, the KY-034 does not require separate PWM signals to control the red, green, and blue LED elements.

The KY-034 is ideal for Arduino, ESP32, Raspberry Pi, robotics, decorative lighting, STEM education, and DIY electronics projects.

Key Features

  • Model: KY-034
  • LED Type: Automatic Color-Changing RGB LED
  • LED Size: 5mm (Typical)
  • Color Effect: Automatic Multicolor Flashing
  • Typical Colors: Red, Green, Blue, Yellow, Cyan, Purple, and White
  • Integrated LED Flashing Controller
  • Operating Voltage: Typically 3.3V–5V DC with Suitable Current Limiting
  • Control Method: Power ON/OFF
  • No External PWM Required
  • 3-Pin Interface: S, +, -
  • Compact PCB Design
  • Suitable for Arduino and Microcontroller Projects

Technical Specifications

Parameter Specification
Model KY-034
Product Type Automatic Flashing Color LED Module
LED Technology RGB LED with Integrated Controller
LED Package 5mm Through-Hole
Number of LEDs 1
Lighting Effect Automatic Color Cycling / Flashing
Typical Color Combinations 7 Colors
Operating Voltage Typically 3.3V–5V DC, Module Dependent
Control Interface Power Switching
PWM Control Not Required
Number of Pins 3
Typical Pin Configuration S / + / -
Board Dimensions Approximately 18.5 × 15mm
Current Limiting Required Unless Integrated
Communication Protocol None

Pin Configuration

Pin Function
S Signal / LED Control Connection (Module Dependent)
+ Positive Supply Connection
- Ground

Note: Some KY-034 versions use only two electrical connections, despite having a three-pin header. Verify the actual PCB markings and circuit before connecting the module.

How It Works

The KY-034 contains a self-flashing RGB LED with an integrated control circuit.

When the LED receives the correct supply voltage and current, its internal controller automatically changes the illuminated colors.

The color-changing sequence is generated inside the LED itself, so a microcontroller does not need to generate individual RGB signals.

Automatic Lighting Sequence

Depending on the installed LED version, the module may cycle through combinations such as:

Red → Green → Blue → Yellow → Cyan → Purple → White

The actual sequence, transition speed, and flashing pattern depend on the LED manufacturer.

Arduino Connection Example

The KY-034 can be powered from a suitable current-limited supply without requiring a microcontroller.

For Arduino-controlled ON/OFF operation, use a suitable transistor driver and current-limiting resistor.

Connection Function
Arduino D8 Transistor control through a suitable resistor
Arduino GND Common ground
KY-034 Connected to the switched, current-limited LED supply

The exact wiring depends on the supplied module's internal circuit and pin arrangement.

Arduino Example Code

The following code switches a suitable external LED driver ON and OFF every three seconds.

const int ledControlPin = 8;

void setup() {
  pinMode(ledControlPin, OUTPUT);
}

void loop() {
  digitalWrite(ledControlPin, HIGH);
  delay(3000);

  digitalWrite(ledControlPin, LOW);
  delay(3000);
}

When powered, the KY-034 automatically produces its programmed color-changing effect.

Note: This example assumes an active-HIGH transistor driver. It does not control individual colors or the LED's internal flashing sequence.

Applications

  • Arduino and ESP32 Projects
  • Raspberry Pi Lighting Projects
  • Automatic Color-Changing Indicators
  • Decorative LED Lighting
  • Robotics Visual Effects
  • DIY Electronic Decorations
  • Interactive Displays
  • Educational STEM Projects
  • Electronic Prototyping
  • Visual Notification Systems
  • Model Lighting and Hobby Projects

Important Notes

  • The KY-034 is an automatic flashing RGB LED module, not a programmable RGB LED module.
  • Its internal controller automatically generates the color-changing sequence.
  • Individual colors generally cannot be selected directly using Arduino PWM.
  • The flashing speed and color sequence are determined by the installed LED.
  • The module does not use the WS2812B or NeoPixel communication protocol.
  • Use appropriate current limiting unless the supplied board already includes a suitable resistor.
  • Do not connect the LED directly to an unrestricted power source.
  • For ESP32 and Raspberry Pi, respect the 3.3V GPIO voltage and current limits.
  • A transistor driver may be required when the LED current exceeds the GPIO's safe output capability.
  • The pin configuration and operating voltage may vary between manufacturers.
  • The module is intended for indicator and decorative lighting rather than high-power illumination.

Package Includes

1 × KY-034 Automatic Flashing Color LED Modules.