BC547 NPN General-Purpose Transistor – 45V, 100mA, TO-92
The BC547 is a popular general-purpose NPN bipolar junction transistor (BJT) designed for low-current switching, signal amplification, sensor interfaces, and general electronics applications.
With a 45V collector-emitter voltage rating, collector current up to 100mA, and compact through-hole TO-92 package, the BC547 is widely used in educational electronics, Arduino projects, amplifier circuits, LED drivers, oscillators, signal processing, and low-power switching applications.
Its low cost, simple operation, and wide range of applications make it one of the most commonly used small-signal transistors in electronics.
Technical Specifications
-
Part Number: BC547
-
Transistor Type: NPN Bipolar Junction Transistor (BJT)
-
Polarity: NPN
-
Collector-Emitter Voltage (VCEO): 45V Max
-
Collector-Base Voltage (VCBO): 50V Max
-
Emitter-Base Voltage (VEBO): 6V Max
-
Continuous Collector Current (IC): 100mA Max
-
DC Current Gain (hFE): Depends on Gain Group
-
Transition Frequency (fT): 100MHz Minimum
-
Collector-Emitter Saturation Voltage: Up to Approx. 200mV at IC = 10mA, IB = 0.5mA
-
Maximum Junction Temperature: +150°C
-
Package: TO-92 / SOT54
-
Number of Pins: 3
-
Mounting Type: Through-Hole
General-Purpose NPN Transistor
The BC547 can be used as both an electronic switch and a small-signal amplifier.
A relatively small current applied to the base controls a larger current flowing between the collector and emitter.
This makes the transistor useful for interfacing low-current control signals with LEDs, buzzers, signal circuits, and other low-power electronic loads.
BC547 Gain Groups
The BC547 family is commonly available in three gain-selected versions:
-
BC547A: hFE 110–220
-
BC547B: hFE 200–450
-
BC547C: hFE 420–800
The gain values are specified under defined datasheet test conditions and will vary with collector current, temperature, and operating conditions.
If your component is marked simply BC547 without an A, B, or C suffix, it is better not to advertise a specific current-gain range.
Switching Applications
The BC547 can be used as a low-current electronic switch for loads such as:
- LEDs
- Buzzers
- Small Signal Relays
- Logic Circuits
- Sensor Outputs
- Low-Current Loads
- Driver Stages
When controlled from an Arduino, ESP32, STM32, Raspberry Pi GPIO, or another microcontroller, an appropriate base resistor should be used.
For inductive loads such as relay coils, a suitable flyback diode should normally be connected across the load.
Signal Amplification
The BC547 is especially well suited to small-signal amplification.
Typical applications include:
- Audio Preamplifiers
- Microphone Amplifiers
- Sensor Signal Conditioning
- Small-Signal Amplifiers
- Oscillators
- Pulse Circuits
- Switching Circuits
- Logic-Level Interfaces
Its relatively high current gain and useful frequency response make it a versatile transistor for analog and digital electronics.
Microcontroller Interface
The BC547 can be used to allow a microcontroller output to control a low-current external load.
A typical low-side switching arrangement is:
- Microcontroller GPIO → Base Resistor → BC547 Base
- BC547 Emitter → Ground
- Load → BC547 Collector
- Other Side of Load → Positive Supply
When separate supplies are used, their grounds normally need to be connected together unless electrical isolation is intentionally provided.
BC547 vs BC337
Although the BC547 and BC337 are both NPN transistors, they should not automatically be treated as equivalent.
BC547: Small-signal transistor, up to approximately 100mA
BC337: General-purpose transistor with significantly higher collector-current capability
For low-current signal amplification and switching, the BC547 is an excellent choice. For loads requiring substantially more current, the BC337 or another appropriately rated transistor may be more suitable.
Important Note
The 100mA collector-current rating is an absolute maximum, not a recommended operating current for every application.
Actual safe operating conditions depend on collector-emitter voltage, base current, ambient temperature, transistor power dissipation, switching duty cycle, and thermal conditions.
The BC547 is intended primarily for low-current switching and small-signal amplification. It should not be used to directly drive high-current motors, large relays, high-power LEDs, or other loads exceeding its electrical and thermal ratings.
Pin configuration may vary between transistor manufacturers and package variants. Always verify the Collector, Base, and Emitter pinout for the exact component supplied before installation.
Applications
Ideal for signal amplification, low-current switching, LED drivers, sensor circuits, audio amplifiers, microphone preamplifiers, oscillators, Arduino projects, microcontroller interfaces, educational electronics, electronics repair, breadboard prototyping, laboratory experiments, and DIY electronics.
Package Includes
1 × BC547 NPN General-Purpose Transistor – TO-92