Robot Pi Shop

CJMCU-TEMT6000 Ambient Light Sensor

$2.50

Shipping calculated at checkout.

Quantity

CJMCU-TEMT6000 Analog Ambient Light Sensor Module

The CJMCU-TEMT6000 Ambient Light Sensor Module is a compact analog light-sensing board designed to measure surrounding visible-light intensity.

It uses the TEMT6000 phototransistor, whose spectral response is designed to closely resemble the sensitivity of the human eye. As ambient light increases, the module produces a corresponding analog voltage that can be measured by the ADC input of an Arduino, ESP32, Raspberry Pi Pico or other microcontroller.

It is ideal for automatic lighting, display brightness adjustment, day/night detection, robotics and environmental monitoring projects.

Technical Specifications

  • Sensor: TEMT6000
  • Sensor Type: Silicon NPN Phototransistor
  • Measurement: Ambient Visible Light
  • Output Type: Analog Voltage
  • Typical Module Supply: 3.3V or 5V DC
  • Maximum Sensor Collector-Emitter Voltage: 6V
  • Peak Sensitivity: 570nm
  • Visible-Light Response: Designed to approximate human-eye sensitivity
  • Angle of Half Sensitivity: ±60°
  • Typical Light Current: 10µA at 20 lux
  • Typical Light Current: 50µA at 100 lux
  • Maximum Sensor Collector Current: 20mA
  • Interface: 3-Pin Analog
  • Pins: VCC, GND, SIG
  • Module Type: CJMCU Breakout Board

Analog Light Output

The module provides an analog output voltage that changes according to the amount of light reaching the TEMT6000 sensor.

In general:

  • Low Light → Lower Analog Output
  • Bright Light → Higher Analog Output

The SIG pin can be connected directly to an ADC-capable input on a compatible microcontroller.

Pin Connections

  • VCC – Power supply
  • GND – Ground
  • SIG – Analog light-level output

Typical Arduino connection:

  • VCC → 5V
  • GND → GND
  • SIG → Analog Input, such as A0

For a 3.3V controller such as ESP32 or Raspberry Pi Pico, the module can be operated from 3.3V, keeping its analog output within the controller's ADC voltage range.

Human-Eye-Like Light Response

Unlike a basic photoresistor, the TEMT6000 is specifically designed as an ambient-light sensor.

Its spectral sensitivity is optimized toward visible light and has a peak response at approximately 570nm, close to the region where the human eye is highly sensitive.

This makes it suitable for applications that need to respond to lighting conditions in a way similar to human visual perception.

Wide Viewing Angle

The TEMT6000 provides an angle of half sensitivity of approximately ±60°, allowing it to detect ambient illumination over a relatively wide area rather than requiring a narrowly focused light source.

Arduino & Microcontroller Compatible

The module can be used with ADC-equipped controllers such as:

  • Arduino Uno
  • Arduino Nano
  • Arduino Mega
  • ESP32
  • STM32
  • Raspberry Pi Pico
  • PIC
  • AVR

and other microcontrollers with analog inputs.

Applications

Ideal for:

  • Automatic Lighting Systems
  • Day / Night Detection
  • Display Brightness Control
  • LCD Backlight Adjustment
  • Smart Home Projects
  • Arduino Projects
  • ESP32 Projects
  • Robotics
  • Environmental Light Monitoring
  • Automatic LED Control
  • Energy-Saving Lighting Systems
  • Educational Electronics
  • DIY Electronics

Important Note

The TEMT6000 provides an analog signal related to light intensity. It is not a calibrated digital lux meter.

While the analog reading can be converted to an estimated illumination value, accuracy depends on the individual sensor, circuit characteristics, ADC reference, supply voltage and lighting spectrum.

For applications requiring precise calibrated lux measurements, a dedicated digital lux sensor may be more suitable.

When using the module with an ESP32 or another 3.3V ADC, powering the sensor module from 3.3V is recommended to prevent the analog output from exceeding the ADC input range.

Package Includes

1 × CJMCU-TEMT6000 Analog Ambient Light Sensor Module