Robot Pi Shop

ENC28J60 Ethernet LAN Network

$3.99

Shipping calculated at checkout.

Quantity

ENC28J60 Ethernet LAN Network Module – SPI, 10Mbps, RJ45, 3.3V

The ENC28J60 Ethernet LAN Network Module provides wired Ethernet connectivity for Arduino, AVR, STM32, PIC and other microcontroller-based projects.

Built around the Microchip ENC28J60 Ethernet controller, the module combines a 10BASE-T Ethernet interface, SPI communication, 25MHz crystal oscillator and HR911105A RJ45 network connector on a compact PCB.

It is ideal for embedded web servers, networked sensors, home automation, robotics and other applications requiring reliable wired Ethernet connectivity.

Technical Specifications

  • Ethernet Controller: Microchip ENC28J60
  • Ethernet Interface: 10BASE-T
  • Network Speed: 10Mbps
  • Host Communication: SPI
  • Maximum SPI Clock: Up to 20MHz
  • Ethernet Standard: IEEE 802.3 Compatible
  • Integrated MAC: Yes
  • Integrated PHY: Yes
  • Packet Buffer: 8KB SRAM
  • Crystal Oscillator: 25MHz
  • RJ45 Network Interface: HR911105A
  • Supply Voltage: 3.3V DC
  • ENC28J60 Digital Inputs: 5V Tolerant
  • Duplex: Full & Half Duplex
  • Module Dimensions: Approx. 58 × 34 × 17mm
  • Interface Type: Wired Ethernet

ENC28J60 Ethernet Controller

The module uses the popular Microchip ENC28J60, a standalone Ethernet controller specifically designed for embedded systems.

The controller integrates:

  • 10BASE-T PHY
  • Ethernet MAC
  • 8KB TX/RX Packet Buffer
  • SPI Host Interface
  • Packet Filtering
  • CRC Generation
  • Collision Handling
  • Interrupt Functions
  • DMA Functions

The host microcontroller communicates with the ENC28J60 through SPI.

HR911105A RJ45 Network Interface

The module includes an HR911105A RJ45 Ethernet connector, providing a convenient connection to standard Ethernet cabling.

This allows the module to connect to compatible:

  • Routers
  • Ethernet Switches
  • Local Area Networks
  • Computers
  • Embedded Network Equipment

10Mbps Ethernet

The ENC28J60 operates using 10BASE-T Ethernet, providing a maximum Ethernet port speed of:

10Mbps

It can be connected to modern Ethernet network equipment that supports 10BASE-T negotiation, but the module itself remains a 10Mbps Ethernet device.

SPI Communication

The module communicates with the host controller through SPI.

Main communication signals include:

  • SO – Serial Data Output / MISO
  • SI – Serial Data Input / MOSI
  • SCK – SPI Clock
  • CS – Chip Select
  • INT – Interrupt Output
  • CLKOUT – Programmable Clock Output

The ENC28J60 supports SPI clock speeds up to 20MHz.

Pin Functions

Typical module connections include:

Pin Function
CLKOUT Programmable Clock Output
INT Interrupt Output
WOL Wake-on-LAN / Module-Specific Connection
SO SPI Serial Output / MISO
SI SPI Serial Input / MOSI
SCK SPI Clock
CS SPI Chip Select
RESET Reset
VCC 3.3V Power Supply
GND Ground

Note: Pin arrangement can vary between ENC28J60 module versions. Always check the PCB markings before wiring.

3.3V Power Supply

The ENC28J60 controller operates from approximately:

3.1–3.6V DC

with 3.3V nominal operation.

The module should therefore be powered from a suitable 3.3V supply unless the specific PCB version explicitly includes a regulator that allows another input voltage.

5V-Tolerant Inputs

The ENC28J60 provides 5V tolerance on specified digital input pins, which can simplify interfacing with some 5V microcontrollers.

However:

5V-tolerant digital inputs do not mean that the module should be powered from 5V.

Use the module's specified 3.3V power input unless the particular board is explicitly marked otherwise.

Arduino Compatibility

The ENC28J60 is widely used for adding Ethernet connectivity to Arduino projects.

With a compatible Ethernet library, applications can include:

  • Embedded Web Servers
  • HTTP Communication
  • TCP/IP Applications
  • UDP Communication
  • Remote Sensor Monitoring
  • Network-Controlled Relays
  • IoT Devices

STM32 & Other Microcontrollers

Because communication is performed through standard SPI, the module can also be integrated with:

  • STM32
  • AVR
  • PIC
  • ESP32
  • ARM Microcontrollers
  • Other SPI-Equipped Controllers

Software support and the appropriate TCP/IP stack are required on the host controller.

Network Features

The ENC28J60 supports features including:

  • Unicast Packets
  • Multicast Packets
  • Broadcast Packets
  • Full-Duplex Operation
  • Half-Duplex Operation
  • Programmable Packet Filtering
  • Automatic CRC Generation
  • Collision Detection & Retransmission
  • Automatic Polarity Detection & Correction

Applications

Ideal for:

  • Arduino Ethernet Projects
  • Embedded Web Servers
  • IoT Devices
  • Home Automation
  • Industrial Monitoring
  • Networked Sensors
  • Remote Data Acquisition
  • Robotics
  • Network-Controlled Relays
  • Access Control Systems
  • Alarm Systems
  • Smart Home Projects
  • STM32 Projects
  • PIC & AVR Projects
  • Educational Networking Projects

Important Notes

  • Ethernet speed is 10Mbps, not 100Mbps.
  • Recommended module supply is 3.3V DC.
  • Do not confuse 5V-tolerant digital inputs with a 5V power-supply rating.
  • Uses SPI communication.
  • TCP/IP functionality is normally handled in software by the host microcontroller.
  • Verify the module's PCB pin labels before connecting it.
  • A compatible ENC28J60 software library or TCP/IP stack is required.
  • Module dimensions may vary slightly between manufacturing versions.

Package Includes

1 × ENC28J60 Ethernet LAN Network Module with RJ45 Connector