GSM/GPRS/GNSS/Bluetooth HAT for Raspberry Pi – SIM868 Quad-Band Module
The Waveshare GSM/GPRS/GNSS/Bluetooth HAT is a multifunctional communication expansion board designed for Raspberry Pi and embedded development projects.
Powered by the SIM868 module, this HAT combines GSM cellular communication, GPRS data connectivity, GNSS satellite positioning, and Bluetooth 3.0 in a compact board.
It enables Raspberry Pi applications to make phone calls, send and receive SMS messages, access 2G mobile data networks, obtain GPS location information, and communicate with Bluetooth devices.
The board includes a standard Raspberry Pi 40-pin GPIO connector, onboard CP2102 USB-to-UART converter, SIM card slot, antenna connectors, and status indicators.
Key Features
-
4-in-1 Communication: GSM, GPRS, GNSS, and Bluetooth
-
Main Module: SIMCom SIM868
-
GSM: Quad-Band 850/900/1800/1900MHz
-
GPRS: Class 12 Mobile Data
-
GNSS: GPS and GLONASS Positioning
-
Bluetooth: Bluetooth 3.0 + EDR
-
Raspberry Pi Interface: Standard 40-Pin GPIO Header
-
USB Communication: Onboard CP2102 USB-to-UART Converter
-
SIM Card Support: 1.8V / 3V SIM Cards
-
Control Interface: UART / AT Commands
-
RTC: Backup Battery Holder
-
Audio: 3.5mm Earphone/Microphone Jack
-
Status Indicators: 6 Onboard LEDs
-
Operating Voltage: 5V DC
Technical Specifications
Main Controller
| Parameter |
Specification |
| Module |
SIMCom SIM868 |
| Cellular Technology |
GSM / GPRS (2G) |
| GNSS |
GPS / GLONASS |
| Bluetooth |
Bluetooth 3.0 + EDR |
| Control Interface |
UART / AT Commands |
| UART Baud Rate |
1200–115200bps, Auto Detection |
| Power Supply |
5V DC |
| GPIO Interface |
Raspberry Pi 40-Pin Header |
| USB-to-UART |
CP2102 |
| Operating Temperature |
-40°C to +85°C |
| Storage Temperature |
-45°C to +90°C |
GSM / GPRS Specifications
GSM Frequency Bands
- GSM 850MHz
- EGSM 900MHz
- DCS 1800MHz
- PCS 1900MHz
- Automatic Quad-Band Selection
- GSM Phase 2/2+ Compatible
Transmitting Power
-
Class 4: 2W at GSM 850/900MHz
-
Class 1: 1W at DCS 1800/1900MHz
GPRS Data
-
GPRS Multislot Class: 12 Default
-
Configurable Classes: 1–12
-
Maximum Downlink Speed: 85.6kbps
-
Maximum Uplink Speed: 85.6kbps
-
Coding Schemes: CS-1, CS-2, CS-3, CS-4
-
PPP Authentication: PAP Supported
-
USSD: Supported
-
PBCCH: Supported
Cellular Functions
- Voice Calls
- SMS Sending and Receiving
- GPRS Data Communication
- HTTP Communication
- FTP Communication
- MMS
- Email Functions
- DTMF
- USSD
- SIM Application Toolkit
Network-dependent functions require a compatible SIM card and an active 2G network.
SMS Features
- Mobile Terminated SMS (MT)
- Mobile Originated SMS (MO)
- Cell Broadcast (CB)
- Text Mode
- PDU Mode
- SIM Card Message Storage
The module can be controlled using standard and SIMCom-specific AT commands.
GNSS Positioning
The integrated GNSS receiver supports satellite-based positioning for tracking and navigation applications.
GNSS Technical Specifications
| Parameter |
Specification |
| Satellite Systems |
GPS / GLONASS |
| Tracking Channels |
33 |
| Acquisition Channels |
99 |
| GPS Signal |
L1 C/A |
| Tracking Sensitivity |
-165dBm |
| Cold Start Sensitivity |
-148dBm |
| Cold Start Time |
Approx. 28s |
| Warm Start Time |
Approx. 26s |
| Hot Start Time |
Less than 1s |
| Horizontal Accuracy |
Less than 2.5m CEP, under suitable conditions |
Positioning Applications
- Vehicle Tracking
- Asset Tracking
- GPS Data Logging
- Fleet Monitoring
- Remote Equipment Monitoring
- Navigation Projects
- IoT Location Systems
The module also supports location-based services through cellular networks where available.
Bluetooth Specifications
-
Bluetooth Version: 3.0 + EDR
-
Communication: Bluetooth Classic
-
Supported Profiles: SPP, OPP, HFP/HSP
-
Control: AT Commands
-
Data Transfer: Supported
-
Wireless Peripheral Communication: Supported
Bluetooth functionality is independent of the Raspberry Pi's onboard Bluetooth hardware.
Raspberry Pi Compatibility
The board features a standard 40-pin Raspberry Pi GPIO expansion header.
It can be used with compatible Raspberry Pi boards supporting the required UART interface.
The onboard UART selection switch allows communication through either the Raspberry Pi GPIO UART or the CP2102 USB-to-UART interface.
UART Selection Modes
-
Position A: Control SIM868 through USB-to-UART
-
Position B: Control SIM868 through Raspberry Pi UART
-
Position C: Access Raspberry Pi UART through USB-to-UART
Onboard Components
-
SIM868 Module: GSM, GPRS, GNSS, and Bluetooth communication
-
ZMM5V1: Protection / Regulation Diode
-
SMF05C: TVS Protection Diode
-
CP2102: USB-to-UART Converter
-
MP1482: Power Management Chip
-
NDC7002N: Voltage Level Translation
-
GPS Indicator: GNSS Status
-
NET Indicator: GSM Network Status
-
STA Indicator: Module Operating Status
-
UART TX/RX Indicators: Serial Communication Activity
-
Power Indicator: Power Status
-
SIM868 Control Button: Power On/Off Control
-
40-Pin GPIO Connector: Raspberry Pi Interface
-
SIM Card Slot: Cellular SIM Installation
-
USB-to-UART Interface: USB Communication
-
3.5mm Audio Jack: Earphone and Microphone
- GNSS Antenna Connector
- Bluetooth Antenna Connector
- GSM Antenna Connector
-
CR1220 Battery Holder: RTC Backup
- UART Selection Switch
Status Indicators
The onboard LEDs help monitor module operation.
NET Indicator
- Fast Flashing: Module Starting or Searching for Network
- Slow Flashing: GSM Network Registration Successful
Other indicators provide information about power, GNSS status, module activity, and UART communication.
Power Requirements
-
Operating Voltage: 5V DC
-
Power Input: Raspberry Pi GPIO / Supported Board Power Interface
-
Power Management: Onboard MP1482
-
Backup Battery: CR1220 Holder for RTC
Important: GSM transmission produces short, high-current bursts. Use a stable 5V supply with sufficient current capacity, especially during cellular network registration and data transmission.
Software & Development
The module is controlled using AT commands.
Supported development platforms include:
- Raspberry Pi
- Arduino
- STM32
- Other UART-Compatible Microcontrollers
AT command functionality includes:
- GSM Network Registration
- SMS Communication
- Voice Calls
- GPRS Connections
- GPS Position Reading
- Bluetooth Communication
- HTTP and FTP Operations
Development examples and documentation are available from Waveshare.
Applications
Ideal for:
- Raspberry Pi IoT Projects
- GSM-Based Monitoring Systems
- GPS Vehicle Tracking
- Asset Tracking
- SMS Alert Systems
- Remote Data Logging
- Cellular Communication Projects
- GPS Navigation
- Fleet Management
- Industrial Monitoring
- Smart Agriculture
- Security Systems
- Embedded Communication Systems
- Educational Projects
- University Projects
Important Notes
-
2G Network Required: The SIM868 supports GSM/GPRS only. It does not support 3G, 4G LTE, or 5G.
-
Network Availability: Confirm that your mobile operator still provides compatible 2G GSM/GPRS service before purchasing.
-
SIM Card: A compatible active SIM card is required for cellular functions.
-
Mobile Data: GPRS is suitable for low-bandwidth applications, not high-speed internet access.
-
GNSS Reception: For best satellite positioning performance, use a suitable GNSS antenna with a clear view of the sky.
-
Power Supply: A stable 5V supply is required.
-
RTC Battery: The CR1220 backup battery may need to be purchased separately.
-
Antenna Accessories: Confirm included antennas against the exact product package.
-
Raspberry Pi: Not included unless specifically stated.
Package Includes
Antennas, cables, and other accessories depend on the supplied package configuration.
Documentation
Manufacturer: Waveshare
Product: GSM/GPRS/GNSS HAT
Documentation and development resources:
https://www.waveshare.com/wiki/GSM/GPRS/GNSS_HAT