Robot Pi Shop

KY-022 IR Infrared Sensor Receiver Module

$1.25

Shipping calculated at checkout.

Quantity

KY-022 IR Infrared Receiver Module – 38kHz Remote Control Sensor for Arduino & ESP32

The KY-022 IR Infrared Receiver Module is a compact infrared sensor designed to receive and decode infrared signals transmitted by compatible remote controls and IR transmitters.

Featuring a 38kHz infrared receiver, commonly based on the VS1838B or an equivalent component, the module detects modulated infrared signals and converts them into digital pulses that can be processed by a microcontroller.

The KY-022 is ideal for Arduino, ESP32, Raspberry Pi, robotics, home automation, remote-controlled devices, and DIY electronics projects.

Key Features

  • Model: KY-022
  • Sensor Type: Infrared Remote Control Receiver
  • Typical Receiver IC: VS1838B or Equivalent
  • Carrier Frequency: 38kHz
  • Operating Voltage: Typically 2.7V–5.5V DC (Receiver Dependent)
  • Output Type: Digital
  • Detection Method: Modulated Infrared Light
  • 3-Pin Interface: Signal (S), VCC (+), GND (-)
  • Compatible with Common IR Remote Control Protocols
  • Compact and Lightweight PCB Design
  • Suitable for Arduino, ESP32, and Raspberry Pi Projects

Technical Specifications

Parameter Specification
Model KY-022
Product Type Infrared Receiver Module
Sensor Technology Infrared Photodetector with Demodulation Circuit
Typical Receiver Component VS1838B or Compatible
Center Carrier Frequency 38kHz
Operating Voltage Typically 2.7V–5.5V DC
Output Type Demodulated Digital Signal
Output Logic Typically Active LOW
Typical Detection Distance Up to Approximately 10–18m Under Suitable Conditions
Typical Reception Angle Approximately ±45° (Receiver Dependent)
Number of Pins 3
Pin Configuration S / + / -
Board Dimensions Approximately 18.5 × 15mm
Communication Interface Digital GPIO
Compatible Protocols NEC, Sony SIRC, RC5, RC6 and Others, Subject to Software Support

Pin Configuration

Pin Function
S Digital Infrared Signal Output
+ Power Supply
- Ground

Arduino Connection Example

KY-022 Arduino Uno
S D2
+ 5V
- GND

The Arduino reads the demodulated infrared signal and uses an infrared decoding library to identify commands transmitted by a compatible remote control.

Arduino Example Code

The following example uses the Arduino-IRremote library (version 4.x).

#include <IRremote.hpp>

const int IR_RECEIVE_PIN = 2;

void setup() {
  Serial.begin(9600);
  IrReceiver.begin(IR_RECEIVE_PIN, ENABLE_LED_FEEDBACK);
}

void loop() {
  if (IrReceiver.decode()) {
    IrReceiver.printIRResultShort(&Serial);
    IrReceiver.resume();
  }
}

How It Works

  1. Connect the KY-022 module to the Arduino.
  2. Install the Arduino-IRremote library through the Arduino IDE Library Manager.
  3. Upload the example code.
  4. Open the Serial Monitor at 9600 baud.
  5. Point a compatible infrared remote control toward the receiver and press a button.
  6. The Arduino displays the received infrared protocol and command information.

Applications

  • Infrared Remote Control Projects
  • Arduino and ESP32 Projects
  • Raspberry Pi Remote Control Input
  • Home Automation Systems
  • Robotics and Automation
  • Wireless Device Control
  • TV Remote Signal Decoding
  • Infrared Communication Experiments
  • Educational STEM Projects
  • DIY Electronics and Prototyping

Important Notes

  • The KY-022 is an infrared receiver, not an infrared transmitter.
  • It is designed primarily for receiving modulated infrared remote-control signals around 38kHz.
  • The module is not intended for measuring distance or detecting ordinary obstacles.
  • Reception distance depends on transmitter power, alignment, ambient light, and environmental conditions.
  • Strong sunlight and certain artificial light sources may interfere with reception.
  • The output is typically active LOW when receiving infrared pulses.
  • The receiver demodulates the infrared carrier; the microcontroller must decode the transmitted command protocol.
  • For ESP32 and Raspberry Pi, power the module at 3.3V if supported by the installed receiver component to maintain safe GPIO logic levels.
  • Verify the pin arrangement and operating voltage of the supplied module before wiring.
  • A compatible infrared transmitter, such as the KY-005 IR Transmitter Module, can be used to create a complete infrared communication system.

Package Includes

1 × KY-022 IR Infrared Receiver Module