L293 Quadruple Half-H Motor Driver IC – Dual H-Bridge, 16-Pin DIP
The L293 Quadruple Half-H Driver IC is a versatile motor driver integrated circuit designed to control inductive loads such as DC motors, bipolar stepper motors, relays, and solenoids.
Featuring four high-current half-H drivers, the L293 can be configured as two full H-bridges, allowing a microcontroller to control the direction and operation of two DC motors or one bipolar stepper motor.
The IC supports separate logic and motor power supplies, making it suitable for Arduino, microcontroller-based robotics, motor control circuits, and electronic prototyping.
Key Features
- Four independently controlled half-H drivers
- Configurable as two full H-bridges
- Controls up to two bidirectional brushed DC motors
- Supports one bipolar stepper motor
- Suitable for relays, solenoids, and other inductive loads
- Separate logic and motor power supply inputs
- TTL-compatible control inputs
- Enable pins for driver activation and PWM control
- Internal protection diodes on the L293D variant
- Standard 16-pin DIP package for breadboard and PCB applications
Technical Specifications
| Parameter |
Specification |
| Model |
L293 |
| IC Type |
Quadruple Half-H Driver |
| Driver Channels |
4 Half-H Drivers |
| Full H-Bridge Configuration |
2 |
| Logic Supply Voltage (VCC1) |
4.5V–7V |
| Motor Supply Voltage (VCC2) |
4.5V–36V |
| Continuous Output Current |
Up to 1A per channel for L293 |
| Peak Output Current |
Up to 2A per channel for L293, non-repetitive |
| Logic Input Compatibility |
TTL-Compatible |
| Enable Inputs |
2 |
| Motor Control |
Forward, Reverse, Stop |
| PWM Speed Control |
Supported |
| Package |
16-Pin DIP |
| Operating Temperature |
Depends on Exact IC Variant |
| Internal Flyback Diodes |
External Diodes Required for L293; Integrated in L293D |
Important: The L293 and L293D have different current ratings. The L293D is typically rated for 600mA continuous output current per channel and 1.2A peak. Verify the exact IC marking before selecting the applicable specifications.
Pin Configuration
| Pin |
Name |
Function |
| 1 |
1,2EN |
Enable Drivers 1 and 2 |
| 2 |
1A |
Driver 1 Logic Input |
| 3 |
1Y |
Driver 1 Output |
| 4 |
GND |
Ground / Heat Dissipation |
| 5 |
GND |
Ground / Heat Dissipation |
| 6 |
2Y |
Driver 2 Output |
| 7 |
2A |
Driver 2 Logic Input |
| 8 |
VCC2 |
Motor Power Supply |
| 9 |
3,4EN |
Enable Drivers 3 and 4 |
| 10 |
3A |
Driver 3 Logic Input |
| 11 |
3Y |
Driver 3 Output |
| 12 |
GND |
Ground / Heat Dissipation |
| 13 |
GND |
Ground / Heat Dissipation |
| 14 |
4Y |
Driver 4 Output |
| 15 |
4A |
Driver 4 Logic Input |
| 16 |
VCC1 |
Logic Power Supply |
How It Works
The L293 contains four half-H driver circuits.
Two half-H drivers can be combined to create one full H-bridge, allowing current to flow through a motor in either direction.
This enables bidirectional motor control using digital signals from a microcontroller.
DC Motor Control Logic
| Enable |
Input 1 |
Input 2 |
Motor Operation |
| HIGH |
HIGH |
LOW |
Rotate in One Direction |
| HIGH |
LOW |
HIGH |
Rotate in Opposite Direction |
| HIGH |
LOW |
LOW |
Both Outputs LOW / Braking |
| HIGH |
HIGH |
HIGH |
Both Outputs HIGH / Braking |
| LOW |
X |
X |
Outputs Disabled / High Impedance |
The motor's physical rotation direction depends on its wiring.
Arduino Connection Example
The following example controls one brushed DC motor using two L293 driver channels.
| L293 Pin |
Arduino / Connection |
| Pin 1 – Enable |
Arduino D9 |
| Pin 2 – Input 1 |
Arduino D7 |
| Pin 7 – Input 2 |
Arduino D8 |
| Pin 3 – Output 1 |
Motor Terminal 1 |
| Pin 6 – Output 2 |
Motor Terminal 2 |
| Pin 8 – VCC2 |
External Motor Supply |
| Pin 16 – VCC1 |
Arduino 5V |
| Pins 4, 5, 12, 13 |
Common Ground |
Use a suitable motor supply and external flyback protection diodes when using the L293 without integrated protection diodes.
Arduino Example Code
const int enablePin = 9;
const int input1 = 7;
const int input2 = 8;
void setup() {
pinMode(enablePin, OUTPUT);
pinMode(input1, OUTPUT);
pinMode(input2, OUTPUT);
}
void loop() {
// Forward
digitalWrite(input1, HIGH);
digitalWrite(input2, LOW);
analogWrite(enablePin, 180);
delay(2000);
// Stop
analogWrite(enablePin, 0);
delay(1000);
// Reverse
digitalWrite(input1, LOW);
digitalWrite(input2, HIGH);
analogWrite(enablePin, 180);
delay(2000);
// Stop
analogWrite(enablePin, 0);
delay(1000);
}
This example rotates the motor in one direction, stops it, and then rotates it in the opposite direction.
Applications
- Arduino Motor Control Projects
- Robotics and Smart Cars
- Bidirectional DC Motor Control
- Bipolar Stepper Motor Driving
- Relay and Solenoid Driving
- Motorized Mechanisms
- Educational Electronics
- Microcontroller-Based Automation
- DIY Motor Driver Circuits
- Electronic Prototyping
Important Notes
- The L293 requires separate connections for logic power and motor power.
- The logic supply must meet the IC's specified operating voltage.
- The motor supply must be selected according to the connected motor.
- The L293 has a relatively high output voltage drop compared with modern MOSFET-based motor drivers.
- Proper thermal management is necessary when operating near the rated output current.
- The L293 requires external flyback diodes for inductive loads, while the L293D includes integrated protection diodes.
- The IC is not suitable for motors exceeding its voltage or current ratings.
- A 3.3V microcontroller may provide compatible logic HIGH signals, but the L293 logic supply must still meet its own voltage requirements.
- Always connect the microcontroller and motor driver grounds together.
- This is a motor driver IC, not a complete motor driver module.
Package Includes
1 × L293 Quadruple Half-H Driver IC – 16-Pin DIP