Robot Pi Shop

MCP2515 Controller and Transceiver Module

$1.75

Shipping calculated at checkout.

Quantity

MCP2515 CAN Bus Controller Module with TJA1050 Transceiver – SPI Interface

The MCP2515 CAN Bus Controller Module is a communication interface designed to add Controller Area Network (CAN) connectivity to Arduino, ESP32, STM32, Raspberry Pi, and other compatible development boards.

The module combines the MCP2515 standalone CAN controller with the TJA1050 CAN transceiver, enabling microcontrollers to transmit and receive CAN messages through an SPI interface.

Supporting CAN 2.0B communication at speeds up to 1Mbps, the module is suitable for automotive electronics, industrial automation, robotics, embedded control systems, and CAN network monitoring.

Key Features

  • MCP2515 CAN Controller: Provides standalone CAN communication through an SPI interface.
  • TJA1050 CAN Transceiver: Converts controller signals into differential CAN bus signals.
  • CAN 2.0B Support: Compatible with standard 11-bit and extended 29-bit CAN identifiers.
  • High-Speed Communication: Supports CAN data rates up to 1Mbps.
  • SPI Interface: Connects to microcontrollers without requiring a built-in CAN controller.
  • 5V Operation: Designed for a regulated 5V DC supply.
  • Message Filtering: Supports hardware acceptance masks and filters.
  • Interrupt Output: Allows the controller to notify the microcontroller of received messages and other events.
  • CANH and CANL Terminals: Screw terminal connection for CAN bus wiring.
  • Compact Design: Suitable for embedded systems, robotics, and industrial communication projects.

Technical Specifications

Parameter Specification
Main Controller MCP2515
CAN Transceiver TJA1050
Module Type CAN Bus Controller and Transceiver
Operating Voltage 5V DC
Communication Interface SPI
CAN Protocol CAN 2.0A / CAN 2.0B
Maximum CAN Bus Speed 1Mbps
CAN Identifier Support 11-bit and 29-bit
CAN Communication Differential CANH / CANL
CAN Controller Buffers 2 Receive Buffers, 3 Transmit Buffers
Acceptance Filters 6
Acceptance Masks 2
Interrupt Support Yes
Oscillator Commonly 8MHz on this module type; verify board marking
CAN Bus Termination Board-dependent; verify installed resistor
CAN Connection Screw Terminal
Maximum Cable Length Up to approximately 1000m at low data rates under suitable conditions
PCB Dimensions Not confirmed

Pin Configuration

Pin Description
VCC 5V DC Power Input
GND Ground
CS SPI Chip Select
SO SPI Data Output (MISO)
SI SPI Data Input (MOSI)
SCK SPI Clock
INT Interrupt Output
CANH CAN Bus High
CANL CAN Bus Low

Arduino UNO Connection Example

MCP2515 Module Arduino UNO
VCC 5V
GND GND
CS D10
SO / MISO D12
SI / MOSI D11
SCK D13
INT D2
CANH CAN Bus High
CANL CAN Bus Low

Connection Instructions:

  1. Connect the MCP2515 module to the Arduino UNO using the SPI connections shown above.
  2. Connect CANH and CANL to the corresponding lines of the CAN network.
  3. Ensure the CAN network has appropriate termination at both physical ends.
  4. Install a compatible MCP2515 CAN library in the Arduino IDE.
  5. Configure the correct oscillator frequency and CAN bus bit rate.
  6. Initialize the CAN controller and configure the required operating mode.
  7. Send or receive CAN messages using the library functions.

CAN Bus Wiring Example

A basic CAN network can include two MCP2515 modules connected to separate microcontrollers.

Module 1 Module 2
CANH CANH
CANL CANL
GND GND (when appropriate for the system grounding design)

Both devices must use the same CAN bit rate and compatible CAN frame settings.

Termination: A typical high-speed CAN bus uses a 120Ω termination resistor at each physical end of the bus. Check whether the module already includes a termination resistor before adding another.

Applications

  • Automotive CAN bus monitoring
  • Vehicle diagnostic development
  • Industrial automation systems
  • Robotics communication networks
  • Arduino CAN bus projects
  • Embedded control systems
  • CAN-based sensor networks
  • Motor controller communication
  • Industrial equipment monitoring
  • CAN data logging
  • Educational CAN protocol projects
  • Distributed microcontroller systems

Important Notes

  • The MCP2515 module operates from a 5V power supply.
  • The TJA1050 transceiver is a 5V device, and the module's SPI signals may not be directly compatible with 3.3V microcontrollers.
  • ESP32, Raspberry Pi, and other 3.3V development boards may require suitable logic-level shifting or a 3.3V-compatible CAN module.
  • The MCP2515 supports Classical CAN (CAN 2.0) and does not support CAN FD.
  • CAN bus communication requires at least two active CAN nodes for normal acknowledged message transmission.
  • CANH and CANL must be connected with the correct polarity.
  • Proper bus termination is required for reliable high-speed communication.
  • The maximum communication distance decreases as the CAN bus bit rate increases.
  • The module does not automatically decode vehicle diagnostic information. OBD-II or other application protocols require additional software and appropriate hardware connections.
  • Verify the onboard oscillator frequency before configuring the CAN library.
  • This module is not galvanically isolated and should not be connected directly to hazardous or incompatible electrical systems.
  • When connecting to an existing vehicle network, use appropriate protection and avoid interfering with safety-critical systems.

Package Includes

  • 1 × MCP2515 CAN Bus Controller Module with TJA1050 Transceiver