The NFC RFID Fingerprint Access Control Relay Module is a versatile electronic access control system that supports three authentication methods: fingerprint recognition, IC cards, and compatible NFC-enabled mobile phones.
Designed for DC 10–120V operation, the module features three selectable relay control modes, adjustable output timing, Normally Open (NO) and Normally Closed (NC) relay contacts, and support for an external exit button.
It is suitable for electronic door locks, smart cabinets, access control systems, and customized electronic switching applications.
Key Features
- Compatible with DC 10–120V power supply.
- Three verification methods: fingerprint, IC card, and compatible mobile phone NFC.
- Three selectable control modes: jog mode, self-locking mode, and ignition mode.
- Adjustable output duration in jog mode, up to 15 minutes.
- Relay with Normally Open (NO) and Normally Closed (NC) output contacts.
- IC card/NFC sensing distance: approximately 25mm.
- Supports an external exit button.
- LED indicators for fingerprint enrollment, verification, deletion, and relay configuration.
Technical Specifications
| Parameter |
Specification |
| Product Type |
NFC RFID Fingerprint Relay Controller |
| Operating Voltage |
DC 10–120V |
| Verification Methods |
Fingerprint, IC Card, Mobile Phone NFC |
| Relay Control Modes |
Jog, Self-Locking, Ignition |
| Jog Mode Timing |
300ms to 15 minutes (selectable presets) |
| Relay Output |
NO / NC |
| IC Card/NFC Sensing Distance |
Approximately 25mm |
| External Exit Button |
Supported |
| Fingerprint Management |
Administrator and Regular Users |
| LED Indicators |
Fingerprint Status and Relay Configuration |
| Relay Contact Rating |
Not specified |
| RFID Frequency |
Not confirmed |
Three Control Modes
1. Inching / Jog Mode
The relay turns on after successful fingerprint recognition and automatically turns off after the finger is released and the configured delay time has elapsed.
2. Self-Locking Mode
The relay turns on after successful fingerprint recognition. After releasing the finger, it remains active until another successful fingerprint recognition toggles it off.
3. Ignition / Hold Mode
The relay remains active while a recognized fingerprint is continuously held against the sensor. It disconnects immediately after the finger is released.
LED Legend (Fingerprint Module)
| LED Color / Status |
Meaning |
| Green |
Action succeeded (enrolled / deleted / verified) |
| Red |
Failed verification |
| Yellow |
Add admin fingerprint mode |
| Pink |
Add regular (user) fingerprint mode |
| Flashing Yellow |
Delete a single admin fingerprint |
| Flashing Pink |
Delete a single regular fingerprint |
| Flashing White |
Delete all regular fingerprints (admins remain) |
| Blue (Panel LED) |
Relay control mode indicator |
Relay Control Modes (Panel Blue LED)
| Blue LED Flashes |
Operating Mode |
| 1 Flash |
Self-Locking (Toggle) |
| 2 Flashes |
Jog (Timed Pulse) |
| 3 Flashes |
Ignition (Hold) |
Jog Mode Delay Settings
The relay activation duration can be configured using the SET button.
How to Adjust the Delay
- Power OFF the board.
- Press and hold the SET button.
- Power ON the board while continuing to hold SET.
- Release SET when the panel's red and blue LEDs turn off.
- Short-press SET to cycle through the available delay settings.
- The red LED blink count indicates the selected delay.
Jog Mode Delay – Red LED Blink Count
| Red LED Blinks |
Output Duration |
| 1 |
300ms |
| 2 |
600ms |
| 3 |
1 second |
| 4 |
2 seconds |
| 5 |
3 seconds |
| 6 |
4 seconds |
| 7 |
5 seconds |
| 8 |
10 seconds |
| 9 |
60 seconds |
| 10 |
15 minutes |
Save the Setting: Touch a valid registered fingerprint or present an authorized card to save the selected delay.
Fingerprint Management (Admin Finger Required)
1. Add Administrator Fingerprint
From factory settings:
- Touch the fingerprint sensor with any finger for approximately 5 seconds.
- Wait for the Yellow LED.
- Press and release the same finger approximately 4–6 times.
- The Green LED indicates successful enrollment.
2. Add Regular User Fingerprint
- Hold a registered administrator finger against the sensor for approximately 10 seconds.
- Wait for the Pink LED.
- Release the administrator finger.
- Place the new user's finger on the sensor as prompted.
- The Blue and then Green indications confirm the enrollment process.
3. Delete a Single Administrator Fingerprint
- Hold an administrator finger against the sensor until the Yellow LED flashes.
- Release the finger.
- Touch the administrator fingerprint to be deleted.
- The Green LED indicates successful deletion.
4. Delete a Single Regular Fingerprint
- Enter the regular fingerprint deletion mode using an administrator fingerprint.
- Wait for the Flashing Pink LED.
- Release the administrator finger.
- Present the registered regular fingerprint to be deleted.
- The Green LED indicates successful deletion.
5. Delete All Regular Fingerprints (Administrators Remain)
- Hold an administrator finger against the sensor until the White LED flashes.
- Release the administrator finger.
- Confirm the deletion operation according to the module's prompts.
- All regular user fingerprints are deleted while administrator fingerprints remain registered.
6. Factory Reset – Delete Everything
- Power ON the board.
- Press and hold the SET button for more than 10 seconds.
- Wait until the panel Red LED and fingerprint module White LED indicate the reset condition.
- Release the SET button.
Important: Factory reset removes stored credentials and configuration according to the controller's reset procedure. Re-enroll administrator credentials before returning the device to normal use.
Demo Mode – Important Security Information
After deleting all stored fingerprints, the module enters demo mode.
- Any fingerprint can activate the relay.
- The fingerprint module still flashes Red to indicate that the fingerprint is not registered.
- The relay can nevertheless activate.
- Demo mode continues until at least one administrator fingerprint is enrolled.
Security Warning: Do not use the device to secure a door, cabinet, or other restricted equipment while demo mode is active. Register an administrator fingerprint and test unauthorized access before installation.
Card / NFC Management
1. Register Administrator Card
After a factory reset, the first registered card becomes the administrator card.
2. Add User Cards
- Present the administrator card for approximately 5 seconds.
- Wait for the audible beep indication.
- Present the user cards to be registered.
- Follow the controller's confirmation indications.
3. Delete a Single Card
- Present the administrator card for approximately 10 seconds.
- Wait for the audible beep indication.
- Present the card to be deleted.
- Follow the controller's confirmation indication.
4. Delete All Cards
The original instructions do not specify the complete procedure for deleting all registered cards. Refer to the controller's instructions before performing this operation.
Connection and Wiring
| Connection |
Function |
| DC Power Input |
DC 10–120V controller power |
| COM |
Relay common contact |
| NO |
Normally Open relay contact |
| NC |
Normally Closed relay contact |
| Exit Button Input |
External push-button activation |
| Fingerprint Reader |
Fingerprint authentication |
| NFC/RFID Reader |
Card and compatible NFC authentication |
Important: Verify the terminal labels and wiring diagram on the supplied board before connecting power or external equipment.
Applications
- Fingerprint door access control
- RFID/NFC electronic lock systems
- Smart cabinets and lockers
- Workshop and equipment access control
- Electronic switching systems
- DIY home automation
- Access-controlled electrical equipment
- Educational security and authentication projects
Important Notes
- The controller requires a DC 10–120V supply.
- The relay contact voltage and current ratings must be verified separately.
- Not all NFC-enabled smartphones support the required credential emulation.
- Confirm the supported RFID card type and frequency before purchasing additional cards.
- An external power supply may be required for the connected electric lock.
- Fingerprint management and delay settings should be tested before final installation.
- Never leave the controller in demo mode when access security is required.
- Some administrative procedures may vary by firmware revision.
Package Includes
- 1 × Relay Control Board
- 1 × Fingerprint Reader Module
- 1 × NFC/RFID Reader Module with Cable
- 1 × RFID Card
- 3 × RFID Key Fobs