The NRF24L01+ PA+LNA 2.4GHz Wireless Transceiver Module with External Antenna is a high-power wireless communication module designed for long-range data transmission between microcontrollers and embedded systems.
Based on the NRF24L01+ transceiver, this module integrates a Power Amplifier (PA) and Low Noise Amplifier (LNA) to improve transmission power and receiver sensitivity compared with standard NRF24L01+ modules.
Operating in the 2.4GHz ISM frequency band, it supports wireless data rates of 250kbps, 1Mbps, and 2Mbps. The included external antenna helps extend communication range, making the module suitable for robotics, remote monitoring, wireless sensor networks, IoT systems, and industrial automation projects.
The module communicates through an SPI interface and is compatible with Arduino, ESP32, Raspberry Pi, STM32, and other development boards.
Key Features
-
PA+LNA Amplification: Integrated power and low-noise amplifiers for extended wireless communication range.
-
High Transmission Power: Up to +20dBm RF output power.
-
External Antenna: Detachable 2dBi antenna for improved wireless coverage.
-
Long-Range Communication: Advertised range up to 520m at 2Mbps under suitable open-area conditions.
-
Bidirectional Wireless Communication: Supports transmitting and receiving data.
-
Multiple Data Rates: 250kbps, 1Mbps, and 2Mbps.
-
SPI Interface: Easy integration with compatible microcontrollers.
-
Automatic Acknowledgment and Retransmission: Improves wireless communication reliability.
-
CRC Error Detection: Helps identify corrupted data packets.
-
Multi-Channel Communication: Supports multiple receiving data pipes.
-
Compact Design: Suitable for robotics and embedded electronics projects.
Technical Specifications
| Parameter |
Specification |
| Product Type |
Wireless RF Transceiver Module |
| RF Chip |
NRF24L01+ |
| Amplifier |
Integrated PA + LNA |
| Operating Frequency |
2.4GHz ISM Band |
| Operating Voltage |
3.0–3.6V DC |
| Recommended Supply Voltage |
3.3V DC |
| Communication Interface |
SPI |
| Wireless Data Rates |
250kbps / 1Mbps / 2Mbps |
| Maximum RF Output Power |
+20dBm |
| Transmission Current |
Approximately 115mA |
| Reception Current |
Approximately 45mA |
| Power-Down Current |
Approximately 4.2µA (module specification) |
| Operating Temperature |
-20°C to +70°C |
| Receiver Sensitivity at 2Mbps |
-92dBm |
| Receiver Sensitivity at 1Mbps |
-95dBm |
| Receiver Sensitivity at 250kbps |
-104dBm |
| PA Gain |
20dB |
| LNA Gain |
10dB |
| LNA Noise Figure |
2.6dB |
| Antenna Gain |
2dBi |
| Antenna Type |
External Detachable Antenna |
| Antenna Connector |
SMA-Type RF Connector |
| Advertised Range at 2Mbps |
Up to 520m (open area) |
| Communication Protocol |
NRF24L01+ Enhanced ShockBurst |
| Modulation |
GFSK |
RF performance, power consumption, and communication distance depend on the module revision, supply stability, antenna installation, interference, and environmental conditions.
Pin Configuration
The module uses an 8-pin interface.
| Pin |
Name |
Description |
| 1 |
GND |
Ground |
| 2 |
VCC |
3.3V DC Power Supply |
| 3 |
CE |
Chip Enable |
| 4 |
CSN |
SPI Chip Select |
| 5 |
SCK |
SPI Clock |
| 6 |
MOSI |
SPI Data Input |
| 7 |
MISO |
SPI Data Output |
| 8 |
IRQ |
Interrupt Output (Optional) |
Connection Example – Arduino UNO
| NRF24L01+ PA+LNA |
Arduino UNO |
| VCC |
External Regulated 3.3V |
| GND |
GND |
| CE |
D9 |
| CSN |
D10 |
| SCK |
D13 |
| MOSI |
D11 |
| MISO |
D12 |
| IRQ |
Optional |
Important: Use an external regulated 3.3V power supply capable of providing sufficient current for the PA+LNA module. The Arduino UNO's onboard 3.3V pin may not provide adequate current during transmission.
Connect the external power supply ground to the Arduino ground.
A 10µF–100µF decoupling capacitor near the module's power pins is recommended to improve supply stability.
Compatible Development Boards
- Arduino UNO
- Arduino Nano
- Arduino Mega
- ESP32 Development Boards
- ESP8266 NodeMCU
- Raspberry Pi
- STM32 Development Boards
- Other microcontrollers supporting SPI communication
Note: The module operates with 3.3V logic. Appropriate voltage-level compatibility must be ensured when using 5V microcontrollers.
Applications
- Long-range wireless robotics
- Remote-controlled vehicles
- Wireless sensor networks
- Arduino-to-Arduino wireless communication
- ESP32 wireless projects
- Industrial monitoring
- Home automation
- Remote data acquisition
- IoT applications
- Agricultural monitoring
- Wireless control systems
- Educational electronics projects
Important Notes
-
Power Supply: Requires a stable 3.3V DC supply. Never connect VCC directly to 5V.
-
Current Requirements: The PA+LNA version consumes significantly more current than the standard NRF24L01+ module.
-
Antenna Installation: Connect the antenna before transmitting to avoid potential damage to the RF amplifier.
-
Communication Range: The advertised 520m range is not guaranteed. Actual performance depends on line of sight, antenna placement, interference, and operating conditions.
-
Compatibility: Can communicate with standard NRF24L01+ modules using matching channel, data rate, address, and communication settings.
-
Communication Type: This is a proprietary 2.4GHz RF transceiver, not a WiFi or Bluetooth module.
-
Software: Commonly used with NRF24L01-compatible libraries such as RF24.
-
Regulatory Compliance: Maximum permitted RF transmission power depends on local wireless regulations.
Package Includes
- 1 × NRF24L01+ PA+LNA Wireless Transceiver Module
- 1 × External 2dBi Antenna