The Omron G2R-1 12V DC Power Relay is a compact, general-purpose electromagnetic relay designed for reliable switching in industrial automation, electronic control circuits, and electrical equipment.
Featuring a 12V DC coil, 10A switching current, and SPDT (Single Pole Double Throw) contact configuration, this relay allows low-power control circuits to switch higher-power electrical loads while providing galvanic isolation between the coil and contacts.
Part of the Omron G2R series, the relay is suitable for PCB mounting and applications requiring dependable switching performance, compact dimensions, and long-term operation.
Key Features
-
12V DC Coil: Suitable for 12V DC control circuits.
-
10A Contact Rating: Designed for switching electrical loads within specified ratings.
-
SPDT Contact Configuration: One changeover contact with Normally Open (NO), Normally Closed (NC), and Common (COM) terminals.
-
PCB Mounting: Through-hole terminals for direct installation on printed circuit boards.
-
Compact Design: Suitable for space-constrained electronic equipment.
-
Electrical Isolation: Electromagnetic switching separates the control circuit from the switched load.
-
Industrial Reliability: Designed for general-purpose electrical and electronic applications.
-
RoHS Compliant: Listed as compliant with RoHS requirements.
-
International Standards: G2R series includes variants with recognized safety approvals.
Technical Specifications
| Parameter |
Specification |
| Manufacturer |
Omron |
| Product Series |
G2R |
| Model |
G2R-1 12VDC |
| Product Type |
Electromagnetic Power Relay |
| Coil Voltage |
12V DC |
| Coil Resistance |
275Ω |
| Approximate Coil Power |
0.52W |
| Contact Configuration |
SPDT (1 Form C) |
| Number of Poles |
1 |
| Contact Terminals |
COM / NO / NC |
| Rated Switching Current |
10A |
| Maximum Switching Voltage (AC) |
380V AC |
| Rated Switching Capacity |
2,500VA |
| Mounting Type |
Through-Hole PCB |
| Operating Temperature |
-40°C to +70°C |
| Approximate Length |
29mm |
| Approximate Width |
13mm |
| Approximate Height |
25.5mm |
| Contact Operation |
Electromagnetic |
| Coil Type |
Non-Latching DC |
Electrical ratings are based on the supplied product information. Permissible switching loads depend on voltage, contact configuration, load type, and the exact relay variant.
Pin Configuration
The G2R-1 relay uses a single changeover contact arrangement.
| Terminal |
Function |
| Coil A1 |
12V DC Coil Connection |
| Coil A2 |
Coil Return |
| COM |
Common Contact |
| NO |
Normally Open Contact |
| NC |
Normally Closed Contact |
Note: Refer to the pin diagram printed on the relay or the official Omron datasheet to identify the exact PCB terminal positions.
Operating Principle
The relay operates using an electromagnetic coil.
When the coil is not energized:
- COM is connected to NC.
- COM is disconnected from NO.
When 12V DC is applied to the coil:
- The electromagnetic mechanism activates.
- COM disconnects from NC.
- COM connects to NO.
When the coil supply is removed, the contacts return to their normal positions.
Connection with Arduino or ESP32
The G2R-1 relay can be controlled using Arduino, ESP32, Raspberry Pi, and other microcontrollers through an appropriate relay driver circuit.
A typical driver circuit includes:
- 12V DC power supply
- Suitable transistor or MOSFET driver
- Flyback protection diode
- Gate or base resistor as required
- Common ground between the driver and controller
Important: Do not connect the relay coil directly to a microcontroller GPIO pin. The coil requires a 12V supply and more current than a GPIO pin can safely provide.
Applications
- Industrial automation
- PLC interface circuits
- Electrical control panels
- Home automation systems
- Appliance control
- Power switching circuits
- Electronic equipment
- Motor control signaling
- Lighting control systems
- Alarm and safety signaling circuits
- DIY electronic control projects
- Embedded control systems
Important Notes
-
Coil Voltage: Use a regulated 12V DC supply.
-
Contact Rating: Do not exceed the specified switching current or voltage.
-
Inductive Loads: Motors, solenoids, and transformers may require contact protection and reduced switching ratings.
-
DC Loads: DC switching capacity differs from AC switching capacity and must be checked against the manufacturer specifications.
-
Flyback Protection: Use a suitable suppression diode or circuit when controlling the coil electronically.
-
PCB Installation: Ensure appropriate PCB trace widths, electrical clearances, and insulation.
-
Electrical Safety: Mains-voltage applications require appropriate electrical protection and qualified installation.
Package Includes