The PN532 NFC RFID Wireless Module V3 is a versatile 13.56MHz contactless communication module based on the NXP PN532 NFC controller. It is designed for reading and writing compatible RFID/NFC tags, contactless communication, and developing NFC-enabled electronic projects.
The module supports I2C, SPI, and UART (HSU) communication interfaces, allowing integration with Arduino, ESP32, Raspberry Pi, and other compatible development boards.
With support for RFID card reading, NFC tag communication, and peer-to-peer (P2P) functionality, the PN532 V3 is suitable for access control systems, identification projects, smart devices, and contactless automation applications.
Its compact PCB design and configurable communication interfaces make it a practical choice for electronics development and prototyping.
Key Features
-
NXP PN532 NFC Controller: Integrated 13.56MHz NFC/RFID communication chip.
-
Multiple Communication Interfaces: Supports I2C, SPI, and High-Speed UART (HSU).
-
RFID Reading and Writing: Communicates with compatible 13.56MHz RFID/NFC cards and tags.
-
NFC Communication: Supports NFC reader/writer and peer-to-peer functionality.
-
Contactless Operation: Enables short-range wireless communication.
-
Microcontroller Compatible: Suitable for Arduino, ESP32, Raspberry Pi, and other supported platforms.
-
Compact PCB Design: Easy to integrate into embedded systems and prototypes.
-
Configurable Interface: Communication mode can be selected according to the board's configuration.
-
Development Support: Compatible with commonly available PN532 software libraries.
Technical Specifications
| Parameter |
Specification |
| Product Model |
PN532 NFC RFID Module V3 |
| Main Controller |
NXP PN532 |
| Operating Frequency |
13.56 MHz |
| Technology |
NFC / RFID |
| Communication Interfaces |
I2C, SPI, UART (HSU) |
| Operating Voltage |
3.3V logic; module supply depends on board configuration |
| RFID Standards |
ISO/IEC 14443 Type A/B, FeliCa |
| NFC Standard |
ISO/IEC 18092 |
| Communication Modes |
Reader/Writer, Peer-to-Peer |
| Antenna |
Integrated PCB Antenna |
| Typical Reading Distance |
A few centimeters, depending on tag and environment |
| Interface Selection |
Configurable on Module |
| Compatible Platforms |
Arduino, ESP32, Raspberry Pi |
Communication Interfaces
| Interface |
Description |
| I2C |
Two-wire communication using SDA and SCL |
| SPI |
Synchronous serial communication using SCK, MOSI, MISO, and SS |
| UART (HSU) |
Serial communication using TX and RX |
Connection Example – Arduino UNO (I2C)
| PN532 Module |
Arduino UNO |
| VCC |
Module-compatible supply |
| GND |
GND |
| SDA |
SDA / A4 |
| SCL |
SCL / A5 |
Note: Configure the module for I2C communication and verify its power supply and logic-level requirements before connecting it.
Applications
- RFID and NFC Card Readers
- Electronic Access Control Systems
- Contactless Identification
- Smart Locks and Security Projects
- NFC Tag Reading and Writing
- Attendance Tracking Systems
- Arduino and ESP32 Projects
- Raspberry Pi NFC Applications
- Smart Home Automation
- Contactless Interactive Devices
- Educational Electronics Projects
Important Notes
-
13.56MHz Only: This module does not support 125kHz RFID cards or tags.
-
Interface Selection: Configure the module for the required I2C, SPI, or UART communication mode before use.
-
Voltage Compatibility: Verify the specific V3 board's supply voltage and logic levels before connecting it to a microcontroller.
-
Card Compatibility: Not all 13.56MHz cards support the same commands, authentication methods, or memory operations.
-
Mobile NFC: Communication with smartphones depends on the phone's NFC capabilities, operating system, and supported protocols.
-
Reading Distance: Actual range depends on antenna positioning, tag size, and environmental conditions.
-
Security: For access control applications, use secure authentication rather than relying only on a card UID.
Package Includes
The product image shows:
- 1 × PN532 NFC RFID V3 Module
- 1 × RFID Key Fob
- 1 × Connection Cable
- 1 × Pin Header