The RC522 RFID Reader/Writer Module is a compact, low-cost 13.56MHz contactless RFID communication module based on the NXP MFRC522 chip. Designed for RFID identification, access control, and embedded electronics projects, it enables contactless reading and writing of compatible RFID cards and key fobs.
The module communicates through an SPI interface and operates at 3.3V DC, making it suitable for integration with Arduino, ESP32, Raspberry Pi, and other microcontroller or single-board computer platforms.
Its compact PCB design, low power consumption, and widely available software libraries make it a practical solution for RFID-based authentication, identification, and automation applications.
Key Features
-
13.56MHz RFID Technology: Supports contactless communication with compatible RFID cards and tags.
-
NXP MFRC522 Chip: Integrated RFID reader/writer IC with modulation, demodulation, and protocol handling.
-
SPI Communication: Easy integration with microcontrollers and development boards.
-
Read and Write Support: Communicates with compatible RFID tags, subject to their access permissions.
-
ISO/IEC 14443 Type A Support: Compatible with supported contactless card protocols.
-
MIFARE Compatibility: Supports selected MIFARE Classic and other compatible 13.56MHz tags.
-
3.3V Operation: Suitable for low-voltage embedded systems.
-
Compact Design: Easy to integrate into electronic projects and custom enclosures.
-
Software Library Support: Compatible with commonly used Arduino and other MFRC522 libraries.
Technical Specifications
| Parameter |
Specification |
| Product Model |
RC522 / MFRC522 |
| Module Type |
RFID Reader/Writer |
| RFID Controller IC |
NXP MFRC522 |
| Operating Frequency |
13.56MHz |
| Operating Voltage |
3.3V DC |
| Operating Current |
13–26mA (supplier specification) |
| Idle Current |
10–13mA (supplier specification) |
| Communication Interface |
SPI |
| Supported Standard |
ISO/IEC 14443 Type A |
| Supported Tags |
Compatible 13.56MHz RFID cards and key fobs |
| Typical Reading Distance |
Approximately 0–5cm, depending on tag and conditions |
| Logic Level |
3.3V |
| Antenna |
Integrated PCB antenna |
| Read/Write Function |
Supported for compatible writable tags |
Pin Configuration
| Pin |
Function |
| SDA / SS |
SPI Slave Select |
| SCK |
SPI Clock |
| MOSI |
SPI Master Out, Slave In |
| MISO |
SPI Master In, Slave Out |
| IRQ |
Interrupt Output |
| GND |
Ground |
| RST |
Reset / Power-Down Control |
| 3.3V |
3.3V DC Power Input |
Connection Example – Arduino UNO
| RC522 Pin |
Arduino UNO |
| SDA / SS |
D10 |
| SCK |
D13 |
| MOSI |
D11 |
| MISO |
D12 |
| IRQ |
Not connected |
| GND |
GND |
| RST |
D9 |
| 3.3V |
3.3V |
Important: The RC522 uses 3.3V logic. A suitable logic-level converter is recommended when connecting its inputs to a 5V Arduino UNO.
Connection Example – ESP32
| RC522 Pin |
ESP32 GPIO |
| SDA / SS |
GPIO 5 |
| SCK |
GPIO 18 |
| MOSI |
GPIO 23 |
| MISO |
GPIO 19 |
| IRQ |
Not connected |
| GND |
GND |
| RST |
GPIO 22 |
| 3.3V |
3.3V |
This example uses the common ESP32 DevKit SPI pin configuration. Connections may differ depending on the ESP32 board.
Applications
- RFID access control systems
- Electronic door locks
- Attendance monitoring systems
- RFID identification projects
- Smart cabinets and lockers
- Inventory and asset identification
- Automated check-in systems
- Educational Arduino and ESP32 projects
- Contactless authentication prototypes
Important Notes
-
3.3V operation only: Do not connect the module's power input directly to 5V.
- The module is designed for compatible 13.56MHz RFID cards and tags.
- It does not support 125kHz RFID cards or key fobs.
- Reading distance depends on antenna design, tag type, orientation, and environmental conditions.
- Not all 13.56MHz cards are compatible; protocol compatibility must be verified.
- Reading or writing protected card data requires the appropriate authentication and permissions.
- This module is not an NFC reader with full support for all NFC protocols.
- Use appropriate software libraries for your selected development board.
Package Includes
Based on the supplied product image:
- 1 × RC522 RFID Reader/Writer Module
- 1 × RFID Contactless Card
- 1 × RFID Key Fob
- Pin Header Strips