Robot Pi Shop

TJA1050 CAN Bus Transceiver Interface Module – 5V High-Speed CAN

$1.99

Shipping calculated at checkout.

Quantity

TJA1050 CAN Bus Transceiver Interface Module – 5V High-Speed CAN

The TJA1050 CAN Bus Transceiver Module is a compact communication interface designed to connect a CAN (Controller Area Network) protocol controller to a physical CAN bus network.

Based on the NXP TJA1050 high-speed CAN transceiver, this module converts the digital transmit and receive signals from a CAN controller into differential CANH and CANL signals, enabling reliable communication between multiple devices.

It is suitable for automotive electronics, industrial automation, robotics, embedded systems, and microcontroller-based CAN communication projects.

The TJA1050 provides improved electromagnetic compatibility (EMC), low electromagnetic emissions, and reliable behavior when a network node is unpowered.

Key Features

  • TJA1050 CAN Transceiver: High-speed CAN physical-layer interface.
  • CAN 2.0 Compatibility: Supports CAN 2.0A and CAN 2.0B networks when used with a compatible CAN controller.
  • High-Speed Communication: Supports CAN bus data rates up to 1 Mbps.
  • Differential Signaling: Uses CANH and CANL for improved noise immunity.
  • 5V Power Supply: Designed for operation from a regulated 5V DC supply.
  • Low Electromagnetic Emissions: Optimized differential output signaling.
  • Unpowered Node Behavior: Designed to minimize interference with the CAN bus when a node is unpowered.
  • Compact PCB: Suitable for embedded electronic projects.
  • Microcontroller Integration: Can interface with Arduino, ESP32, STM32, and other platforms equipped with a compatible CAN controller.
  • High-Speed CAN Interface: Suitable for multi-node CAN networks.

Technical Specifications

Parameter Specification
Product Type CAN Bus Transceiver Module
Main IC TJA1050
Manufacturer of IC NXP Semiconductors
Communication Protocol Classical CAN
CAN Standard ISO 11898-2 High-Speed CAN
Maximum Data Rate 1 Mbps
Operating Voltage 5V DC
Typical Supply Voltage 5V
Communication Signals TXD, RXD
CAN Bus Signals CANH, CANL
Signaling Type Differential
CAN Controller Required Yes
Standby Mode Not supported
PCB Dimensions Approximately 22 × 11.5 mm
Interface Pin-header connections

Pin Configuration

Pin Description
VCC / 5V 5V DC power supply
GND Ground
TXD Transmit data input from CAN controller
RXD Receive data output to CAN controller
CANH CAN bus high signal
CANL CAN bus low signal

Note: Verify the printed pin labels on the actual module before wiring, as PCB layouts may vary.

Connection Examples

Arduino with MCP2515 CAN Controller

The TJA1050 can be connected to an MCP2515 CAN controller to provide CAN bus communication.

TJA1050 Module MCP2515 Controller Circuit
VCC 5V
GND GND
TXD CAN TX output
RXD CAN RX input
CANH CAN Bus High
CANL CAN Bus Low

The MCP2515 communicates with Arduino through SPI, while the TJA1050 handles the physical CAN bus signals.

ESP32 CAN Bus Connection

ESP32 microcontrollers with a built-in TWAI (CAN-compatible) controller can use an external CAN transceiver such as the TJA1050.

TJA1050 Module ESP32
VCC 5V regulated supply
GND GND
TXD ESP32 TWAI TX GPIO
RXD ESP32 TWAI RX GPIO through suitable level shifting
CANH CAN Bus High
CANL CAN Bus Low

Important: The TJA1050 is a 5V transceiver. Its RXD output may reach 5V and must not be connected directly to a non-5V-tolerant ESP32 GPIO. Use appropriate level shifting or choose a 3.3V-compatible CAN transceiver.

Applications

  • Automotive CAN Bus Communication
  • Industrial Automation Systems
  • Robotics and Mobile Robots
  • Motor Controller Communication
  • CAN-Based Sensor Networks
  • Embedded Control Systems
  • Vehicle Diagnostic Development
  • Arduino and ESP32 CAN Projects
  • Industrial Equipment Monitoring
  • Multi-Node Communication Networks

Important Notes

  • The TJA1050 is a CAN transceiver, not a standalone CAN controller.
  • A separate CAN controller, such as the MCP2515, or a microcontroller with an integrated CAN controller is required.
  • The module requires a regulated 5V power supply.
  • For ESP32 and other 3.3V microcontrollers, ensure that signal voltage levels are compatible.
  • A properly designed high-speed CAN bus typically requires 120Ω termination at each physical end of the bus.
  • Verify whether the module includes a termination resistor before adding external termination.
  • The TJA1050 supports Classical CAN, not CAN FD data-phase operation.
  • Use twisted-pair wiring for CANH and CANL to improve noise immunity.
  • The module does not provide galvanic isolation.

Package Includes

  • 1 × TJA1050 CAN Bus Transceiver Interface Module