Robot Pi Shop

W1209 Digital Temperature Controller Thermostat with Waterproof Sensor

$5.99

Shipping calculated at checkout.

Quantity

W1209 Digital Temperature Controller Thermostat with Waterproof Sensor

The W1209 Digital Temperature Controller is a compact, programmable thermostat module designed for automatic heating and cooling control. Equipped with a digital LED display, relay output, and waterproof NTC temperature probe, it provides a convenient solution for monitoring and regulating temperature in electronic and automation projects.

The controller automatically switches connected heating or cooling equipment ON or OFF according to the configured temperature settings. Its three onboard buttons allow easy adjustment of the target temperature, hysteresis, and other operating parameters without requiring programming.

The included protective case helps protect the circuit board from accidental contact and minor mechanical damage.

Key Features

  • Automatic Temperature Control: Switches connected equipment ON or OFF according to the selected temperature.
  • Heating and Cooling Modes: Supports both heating and cooling applications.
  • Wide Temperature Range: Supports temperature control from -50°C to +110°C.
  • Waterproof Temperature Probe: External NTC sensor for temperature measurement.
  • Digital LED Display: Three-digit display shows the measured temperature and configuration settings.
  • Adjustable Temperature Settings: Configure target temperature and switching hysteresis.
  • Relay Output: Controls external heating or cooling devices.
  • Three-Button Interface: Easy configuration without programming.
  • Relay Status Indicator: Onboard LED indicates relay operation.
  • Protective Case: Enclosure provides additional protection for the controller PCB.
  • Compact Design: Suitable for DIY electronics, automation, and temperature regulation systems.

Technical Specifications

Parameter Specification
Model W1209
Product Type Digital Temperature Controller
Temperature Control Range -50°C to +110°C
Temperature Sensor External NTC Thermistor
Sensor Type Waterproof Probe
Display 3-Digit LED Display
Display Resolution 0.1°C from -9.9°C to 99.9°C
Display Resolution Outside Range 1°C
Temperature Refresh Interval Approximately 0.5 Seconds
Operating Modes Heating / Cooling
Control Method Relay ON/OFF
Relay Rating Up to 10A at 14V DC or 5A at 240V AC, as listed
User Interface 3 Push Buttons
Relay Indicator LED
Enclosure Protective Case

Note: The original listing specifies 0.1°C measurement and control accuracy. These values should not be interpreted as guaranteed accuracy without calibration or manufacturer verification.

Temperature Control Modes

Heating Mode

The controller activates the relay when the measured temperature falls below the configured switching threshold and deactivates it when the target temperature is reached.

Suitable for:

  • Small Heating Systems
  • Incubators
  • Temperature-Controlled Enclosures
  • DIY Heating Projects

Cooling Mode

The controller activates the relay when the measured temperature rises above the configured switching threshold and deactivates it when the temperature returns to the desired level.

Suitable for:

  • Cooling Fans
  • Electronic Equipment Cooling
  • Small Refrigeration Projects
  • Temperature-Controlled Cabinets

Control Buttons

Button Function
SET Access and confirm temperature settings
+ Increase selected value
− Decrease selected value

The controller supports adjustable parameters such as temperature hysteresis, calibration offset, and delay settings, depending on the firmware version.

Connection and Wiring

The W1209 typically includes connections for the power supply, temperature probe, and relay-controlled load.

Connection Function
DC Power Input Powers the thermostat controller
NTC Sensor Connector Connects the external temperature probe
Relay COM Common Relay Contact
Relay NO Normally Open Relay Contact
Relay NC Normally Closed Relay Contact, if provided

The relay acts as a switching contact and does not supply power to the connected load.

Applications

  • Incubator Temperature Control
  • Heating and Cooling Systems
  • Aquarium Temperature Monitoring
  • Electronic Equipment Cooling
  • DIY Thermostat Projects
  • Temperature-Controlled Cabinets
  • Small Refrigeration Systems
  • Industrial Prototyping
  • Educational Electronics Projects

Important Notes

  • Verify the module's supply voltage before connecting power. Standard W1209 boards commonly use 12V DC, but the exact supplied version should be confirmed.
  • The waterproof rating applies to the temperature probe, not the controller or protective case.
  • Do not immerse the controller board or enclosure in water.
  • Ensure the connected load does not exceed the relay's voltage and current ratings.
  • For high-power equipment, use a suitably rated external relay or contactor.
  • Mains-voltage wiring must be installed with appropriate insulation, protection, and electrical safety precautions.
  • The controller provides ON/OFF temperature regulation, not PID control.
  • Temperature measurement accuracy depends on the NTC sensor, calibration, and operating conditions.

Package Includes

  • 1 × W1209 Digital Temperature Controller
  • 1 × Waterproof NTC Temperature Probe
  • 1 × Protective Case