YF-S201C Transparent Water Flow Sensor – G1/2", 1–30 L/min
The YF-S201C Transparent Water Flow Sensor is a compact Hall-effect flow meter designed to measure water flow in pipelines, water heaters, automatic dispensers, irrigation systems, and electronic water monitoring applications.
Featuring a transparent plastic housing, the sensor allows visual inspection of the internal turbine and water flow. Its integrated Hall-effect sensor detects the rotation of the magnetic rotor and generates electrical pulses proportional to the water flow rate.
With a 1–30 L/min flow measurement range, 5–15V DC operating voltage, and G1/2" threaded connections, the YF-S201C is suitable for integration into Arduino, ESP32, and other microcontroller-based monitoring systems.
Key Features
-
Hall-Effect Flow Measurement: Detects water flow using a magnetic rotor and Hall-effect sensor.
-
Transparent Housing: Allows visual inspection of the internal rotor and water passage.
-
1–30 L/min Flow Range: Suitable for various water monitoring applications.
-
5–15V DC Operation: Supports low-voltage electronic control systems.
-
Digital Pulse Output: Generates electrical pulses corresponding to water flow.
-
G1/2" Threaded Connections: Designed for installation in compatible water pipelines.
-
Integrated Turbine Mechanism: Converts water movement into rotational motion for measurement.
-
Water and Electronics Separation: Designed to isolate the sensing electronics from the water passage.
-
Compact Construction: Suitable for integration into automated equipment.
-
Microcontroller Compatible: Can be used with Arduino, ESP32, and Raspberry Pi through suitable signal interfacing.
Technical Specifications
| Parameter |
Specification |
| Model |
YF-S201C |
| Product Type |
Water Flow Sensor |
| Sensor Technology |
Hall Effect |
| Housing Material |
Transparent Plastic |
| Housing Color |
Transparent |
| Operating Voltage |
5–15V DC |
| Flow Measurement Range |
1–30 L/min |
| Pipe Connection |
G1/2" Thread |
| Output Signal |
Digital Pulse |
| Internal Mechanism |
Magnetic Turbine Rotor |
| Electrical Connection |
3-Wire |
| Sensor Application |
Water Flow Measurement |
| Compatible Controllers |
Arduino, ESP32, Raspberry Pi (with appropriate interfacing) |
Pin Configuration
The YF-S201C uses a three-wire electrical connection.
| Wire Color |
Function |
Connection |
| Red |
VCC |
Positive DC Supply |
| Black |
GND |
Ground |
| Yellow |
Signal |
Digital Pulse Output |
Working Principle
The YF-S201C measures water flow using a turbine-based Hall-effect sensing mechanism.
- Water enters the sensor through the inlet connection.
- The flowing water rotates the internal turbine.
- A magnetic rotor rotates together with the turbine.
- The Hall-effect sensor detects the changing magnetic field.
- The sensor generates electrical pulses corresponding to the turbine rotation.
- A connected controller counts these pulses to calculate water flow rate and estimate total water consumption.
The pulse frequency increases as the water flow rate increases.
Note: Accurate measurement requires the correct pulse-to-flow calibration factor, which should be confirmed from the manufacturer's documentation or established through calibration.
Connection with Arduino
| YF-S201C |
Arduino |
| Red (VCC) |
5V |
| Black (GND) |
GND |
| Yellow (Signal) |
Digital Input D2 |
The Arduino can count incoming pulses using a digital input and calculate the approximate water flow rate.
Connection with ESP32
| YF-S201C |
ESP32 |
| Red (VCC) |
5V Supply |
| Black (GND) |
GND |
| Yellow (Signal) |
GPIO via Compatible Signal Interface |
Important: ESP32 GPIO pins operate at 3.3V logic levels. Verify the sensor's output voltage and use an appropriate pull-up or level-shifting circuit where required.
Applications
- Water Flow Monitoring Systems
- Smart Irrigation Systems
- Automatic Water Dispensers
- Water Heater Flow Detection
- Arduino and ESP32 Projects
- Water Consumption Monitoring
- Smart Home Automation
- Agricultural Water Monitoring
- Water Pump Monitoring
- Liquid Flow Measurement Equipment
- Educational Electronics Projects
Important Notes
-
Operating Voltage: Use a suitable DC power supply within the specified 5–15V range.
-
Installation Direction: Install the sensor according to the indicated water flow direction.
-
Pipe Compatibility: Ensure the plumbing connections match the G1/2" threads.
-
Flow Calibration: Accurate flow measurement requires a suitable calibration factor.
-
ESP32 and Raspberry Pi: Use appropriate voltage-level interfacing to protect 3.3V GPIO pins.
-
Water Compatibility: Designed for water flow measurement; compatibility with other liquids must be verified.
-
Pressure and Temperature: Confirm the maximum allowable operating pressure and liquid temperature before installation.
-
Potable Water: Do not assume drinking-water certification without manufacturer documentation.
-
Flow Control: This sensor measures water flow but does not control or stop the water supply.
-
Transparent Housing: Allows visual inspection but does not eliminate the need for regular maintenance.
Package Includes